Arduino MKR Wifi 1010 met headers

Swipen voor 2 additionele foto's
€ 31,90 € 26,36
14 in voorraad
De Arduino MKR 1010 is een krachtig programmeerbord dat de functionaliteit van de zero en de Wifi shield combineert. Ideaal voor het ontwerpen van IoT projecten met een minimale ervaring in netwerken. De nieuwste versie van de MKR 1000 Wifi maar met ESP32 module on board made by UBLOX.
Meer informatie
Meer informatie
Referentie ABX00023
Nummer leverancier P2-6
Technische specificaties
  • The MKR WIFI 1010 is a significant improvement on the MKR 1000 WIFI. It's equipped with an ESP32 module made by U-BLOX. This board aims to speed up and simplify the prototyping of WiFi based IoT applications thanks to the flexibility of the ESP32 module and its low power consumption.

    The board is composed of three main blocks:

    • SAMD21 Cortex-M0+ 32bit Low Power ARM MCU;
    • U-BLOX NINA-W10 Series Low Power 2.4GHz IEEE® 802.11 b/g/n Wi-Fi; and
    • ECC508 Crypto Authentication. (datasheet)

    The MKR WIFI 1010 includes 32-bit computational power, the usual rich set of I/O interfaces, and low power Wi-Fi with a Cryptochip for secure communication using SHA-256 encryption. Plus, it offers ease of use Arduino Software (IDE) for code development and programming. All of these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form.

    Its USB port can be used to supply power (5V) to the board. It has a Li-Po charging circuit that allows the Arduino MKR WIFI 1010 to run on battery power or an external 5 volt source, charging the Li-Po battery while running on external power. Switching from one source to the other is done automatically.

    Warning: Unlike most Arduino boards, the MKR WIFI 1010 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

    • Microcontroller SAMD21 Cortex-M0+ 32bit Low Power ARM MCU
      Board Power Supply (USB/VIN) 5V
      Supported Battery(*) Li-Po Single Cell, 3.7V, 700mAh Minimum
      Circuit Operating Voltage 3.3V
      Digital I/O Pins 8
      PWM Pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
      UART 1
      SPI 1
      I2C 1
      I2S 1
      Connectivity WiFi
      Analog Input Pins 7 (ADC 8/10/12 bit)
      Analog Output Pins 1 (DAC 10 bit)
      External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
      DC Current per I/O Pin 7 mA
      Flash Memory 256 KB
      SRAM 32 KB
      EEPROM No
      Clock Speed 32.768 kHz (RTC), 48 MHz
      Full-Speed USB Device and Embedded Host Included
      Length 61.5 mm
      Width 25 mm
      Weight 32 gr.

* Ondanks een zeer uitgebreid stocksysteem, is het mogelijk dat de voorraadstatus niet overeenstemt met de actuele voorraad. Aarzel niet ons te contacteren, indien u zekerheid wenst over de beschikbaarheid.

** De weergegeven foto bij de producten kan verschillen van het eigenlijke product.